TESTED up to 20240716 ===================== p=programmed OK x=already programmed or not tested c=checked OK -=checked not OK e=checked OK with chips excluded from readout column 1: full test in testrigg files in mcm// column 2: pedestal test, different gains&polarity with LVCARD files in: /mcm-clk0-ped0-thr0-gain-s0-p1-s0-test1.csv /mcm-clk0-ped0-thr0-gain-s0-p1-s0-test1.csv.pdf 12 date nb id chipid comment p cx 20240712 mcm10 4C11 530 x xc 20240930 mcm10 4C11 530 x cx 20240617 mcm11 5810 518 already programmed, redone, now ok (previous no signal on chip0 chan6) x cx 20240712 mcm11 5810 518 redone x xc 20241001 mcm11 5810 518 p cx 20240712 mcm12 8815 544 chip6 chan8 slope? x xc 20240930 mcm12 8815 544 x cx 20240712 mcm13 2414 526 x xc 20240930 mcm13 2414 526 p -x 20240709 mcm20 300F 573 bit errors (op changed) x cx 20240712 mcm20 300F 573 x xc 20240930 mcm20 300F 573 p -x 20240709 mcm21 3C0F 558 vrefp wrong(op changed) x -x 20240712 mcm21 3C0F 558 vrefp wrong (op changed) x -x 20240924 mcm21 3C0F 558 vrefp,incm wrong (op changed) x x- 20240930 mcm21 3C0F 558 high current - -- -------- mcm22 1415 --- on smalltpc - -- -------- mcm23 4012 --- on smalltpc p cx 20240612 mcm30 1A12 132 x xc 20240930 mcm30 1A12 132 p cx 20240612 mcm31 640F 120 x xc 20240612 mcm31 640F 120 p cx 20240612 mcm32 2A13 131 x xc 20240930 mcm32 2A13 131 p -x 20240613 mcm33 3E11 134 global reset, mcmdumpregs fail x -x 20240701 mcm33 3E11 134 global reset; same x -x 20240716 mcm33 3E11 134 chip4,5 no answer x -x 20240924 mcm33 3E11 134 exclude chip4,5 bit errors x x- 20241001 mcm33 3E11 134 exclude chip4,5 bit errors p cx 20240613 mcm40 7411 97 x -x 20240924 mcm40 7411 97 1.5V 1A x x- 20240931 mcm40 7411 97 1.5V 1A p cx 20240613 mcm41 2C10 91 x xc 20240930 mcm41 2C10 91 p cx 20240613 mcm42 1412 93 x xc 20240930 mcm42 1412 93 p cx 20240613 mcm43 3410 119 x xc 20240930 mcm43 3410 119 p -x 20240613 mcm50 4812 491 bit 2 always set x -x 20240701 mcm50 4812 491 chip3,4,5 bit2; chip7 chan0 no signal x -x 20240709 mcm50 4812 491 chip3,4,5 bit2 x -x 20240716 mcm50 4812 491 chip3,4 bit 0x2 c_1v5 2V x ex 20240924 mcm50 4812 491 exclude chip 3,4 frpm readout then OK x xe 20241001 mcm50 4812 491 exclude chip 3,4 frpm readout then OK p cx 20240613 mcm51 7216 650 x xc 20240930 mcm51 7216 650 p - 20240613 mcm52 ---- 662 current2.5V, mcmdump failed x - 20240617 mcm52 ---- 662 current2.5V, mcmdump failed x - 20240701 mcm52 ---- 662 mcmdump failed : cv2.5; same (bo 100ohm resistor?) x - 20240924 mcm52 8215 662 chip 3,4,5 no reply x - 20240924 mcm52 8215 662 chip 3,4,5 excluded, hangs p cx 20240613 mcm53 6C0F 490 x xc 20240930 mcm53 6C0F 490 p -x 20240613 mcm60 3C11 413 no signal chip4 chan4 x -x 20240617 mcm60 3C11 413 redone,no signal chip4 chan4 x -x 20240701 mcm60 3C11 413 (redone,no signal chip4 chan4 now OK) chip7 chan0 no signal x -x 20240709 mcm60 3C11 413 global reset bit error x cx 20240716 mcm60 3C11 413 x xc 20240930 mcm60 3C11 413 p -x 20240613 mcm61 3214 421 no signal chip4 chan4 x cx 20240617 mcm61 3214 421 redone, OK now x xc 20240930 mcm61 3214 421 p cx 20240617 mcm62 5612 409 x xc 20240930 mcm62 5612 409 p cx 20240617 mcm63 3611 429 x xc 20240930 mcm63 3611 429 p cx 20240617 mcm70 5012 642 x x- 20240930 mcm70 5012 642 Could not read CPLD x xc 20241001 mcm70 5012 642 p cx 20240617 mcm71 6A16 670 x xc 20240930 mcm71 6A16 670 p cx 20240617 mcm72 7C12 678 x xc 20240930 mcm72 7C12 678 p cx 20240617 mcm73 2A14 658 x xc 20240930 mcm73 2A14 658 p cx 20240618 mcm80 1016 473 x xc 20240930 mcm80 1016 473 p cx 20240618 mcm81 1816 475 x xc 20240930 mcm81 1816 475 p cx 20240618 mcm82 7025 455 x xc 20240930 mcm82 7025 455 p cx 20240618 mcm83 5A13 449 x xc 20240930 mcm83 5A13 449 p cx 20240618 mcm90 2214 295 x xc 20240930 mcm90 2214 295 p cx 20240618 mcm91 4611 253 x xc 20240930 mcm91 4611 253 p cx 20240618 mcm92 6213 282 x xc 20240930 mcm92 6213 282 p cx 20240618 mcm93 1215 241 x xc 20240930 mcm93 1215 241 p -x 20240618 mcm100 4411 513 chip7 chan0 no signal x cx 20240709 mcm100 4411 513 x xc 20240930 mcm100 4411 513 p cx 20240618 mcm101 5E10 508 x xc 20240930 mcm101 5E10 508 p cx 20240618 mcm102 5C13 504 x xc 20240930 mcm102 5C13 504 p cx 20240618 mcm103 2C14 486 x xc 20240930 mcm103 2C14 486 p cx 20240625 mcm110 762B 418 x xc 20240930 mcm110 762B 418 p -x 20240625 mcm111 5610 410 chip7 chan0 no signal x cx 20240709 mcm111 5610 410 x xc 20240930 mcm111 5610 410 p cx 20240625 mcm112 3414 403 x xc 20240930 mcm112 3414 403 p -x 20240625 mcm113 7016 404 chip7 chan0 no signal x cx 20240709 mcm113 7016 404 x xc 20240930 mcm113 7016 404 p cx 20240625 mcm120 6E15 571 x xc 20241001 mcm120 6E15 571 p cx 20240625 mcm121 6413 576 x xc 20241001 mcm121 6413 576 p cx 20240625 mcm122 5613 575 (SRU hanged once), redo OK x xc 20241001 mcm122 5613 575 p -x 20240625 mcm123 4612 391 chip7 chan0 no signal, SRU hang x cx 20240709 mcm123 4612 391 x xc 20241001 mcm123 4612 391 p cx 20240625 mcm130 6610 460 x xc 20241001 mcm130 6610 460 p cx 20240625 mcm131 8416 444 x xc 20241001 mcm131 8416 444 p cx 20240625 mcm132 8015 458 x xc 20241001 mcm132 8015 458 p cx 20240625 mcm133 320F 476 x xc 20241001 mcm133 320F 476 p cx 20240628 mcm140 722E 098 chip6 chan 8: slope up when pulsing x cx 20240813 mcm140 722E 098 ok(no slope?) x xc 20241001 mcm140 722E 098 p -x 20240628 mcm141 2212 100 chip6 chan 8: slope up when pulsing?, chip7 chan0: no signal x cx 20240709 mcm141 2212 100 x xc 20241001 mcm141 2212 100 ca ch64 high ped? p cx 20240628 mcm142 4215 720 chip6 chan 8: slope up when pulsing + slight on others? x xc 20241001 mcm142 4215 720 p cx 20240628 mcm143 2C13 717 chip6 chan 8: slope up when pulsing? x xc 20241001 mcm143 2C13 717 p cx 20240628 mcm150 7A16 665 chip6 chan 8: slope up when pulsing? x xc 20241001 mcm150 7A16 665 p -x 20240628 mcm151 E16 679 chip7 chan0: no signal x cx 20240709 mcm151 E16 679 x xc 20241001 mcm151 E16 679 p cx 20240628 mcm152 4E12 691 x xc 20241001 mcm152 4E12 691 p cx 20240628 mcm153 5E14 677 x xc 20241001 mcm153 5E14 677 sometimes for full run gain0: chip0&7 ped=0 - -x 20240628 mcm160 ---- 271 programming; Expected: 0x612B4043 Read: 0x00000000 - -x 20240712 mcm160 ---- 271 (Expected: 0x612B4043 Read: 0x00000000). p cx 20240924 mcm160 1A15 271 p xc 20241001 mcm160 1A15 271 p -x 20240628 mcm161 6216 289 chip7 chan0 no signal x cx 20240709 mcm161 6216 289 x xc 20241001 mcm161 6216 289 p cx 20240628 mcm162 3A14 281 x xc 20241001 mcm162 3A14 281 p -x 20240628 mcm163 6A13 800 bit error chip3,4 (grst,ramp,pulser,data) x -x 20240716 mcm163 6A13 800 bit error chip3,4 0x80 x ex 20240716 mcm163 6A13 800 exclude chip3,4 x xe 20241001 mcm163 6A13 800 exclude chip3,4 p -c 20240701 mcm170 6010 718 chip7 chan0 no signal x -x 20240709 mcm170 6010 718 chip5 chan7 short to GND x cx 20240709 mcm170 6010 718 tester repaired OK x xc 20241001 mcm170 6010 718 tester repaired OK - -x 20240701 mcm171 ---- 686 Expected: 0x612B4043 Read: 0xFFFFFFFF p -x 20240712 mcm171 7611 686 bit error, chip 3&4 x -x 20240716 mcm171 7611 686 bit error on chip 3&4 0x80 c_1v5 low x ex 20240924 mcm171 7611 686 exclude chip3,4 x xe 20241001 mcm171 7611 686 exclude chip3,4 p -x 20240701 mcm172 7417 695 ADC after DAC init (action 3), data strange all over x -x 20240716 mcm172 7417 695 incm=225 ca = as refn p -x 20240701 mcm173 6E0F 710 chip7 chan0 no signal (refcm high?) x cx 20240709 mcm173 6E0F 710 x xc 20241001 mcm173 6E0F 710 bad mcms -------- p - 20240709 mcm21 3C0F 558 vrefp wrong(op changed) x - 20240712 mcm21 3C0F 558 vrefp wrong (op changed) p - 20240613 mcm33 3E11 134 global reset, mcmdumpregs fail x - 20240701 mcm33 3E11 134 global reset; same x - 20240716 mcm33 3E11 134 chip4,5 no answer p - 20240613 mcm50 4812 491 bit 2 always set x - 20240701 mcm50 4812 491 chip3,4,5 bit2; chip7 chan0 no signal x - 20240709 mcm50 4812 491 chip3,4,5 bit2 x - 20240716 mcm50 4812 491 chip3,4 bit 0x2 c_1v5 2V p - 20240613 mcm52 ---- 662 current2.5V, mcmdump failed x - 20240617 mcm52 ---- 662 current2.5V, mcmdump failed x - 20240701 mcm52 ---- 662 mcmdump failed : cv2.5; same (no 100ohm resistor?) - - 20240628 mcm160 --- 271 programming; Expected: 0x612B4043 Read: 0x00000000 - - 20240712 mcm160 --- 271 (Expected: 0x612B4043 Read: 0x00000000). p - 20240628 mcm163 6A13 800 bit error chip3,4 (grst,ramp,pulser,data) x - 20240716 mcm163 6A13 800 bit error chip3,4 0x80 - - 20240701 mcm171 ---- 686 programming Expected: 0x612B4043 Read: 0xFFFFFFFF p - 20240712 mcm171 7611 686 bit error on chip 3&4 x - 20240716 mcm171 7611 686 bit error on chip 3&4 0x80 c_1v5 low p - 20240701 mcm172 7417 695 ADC after DAC init (action 3), data strange all over x - 20240716 mcm172 7417 695 incm=225 ca as refn Proposed retest at least: x - 20240701 mcm33 3E11 134 global reset; same x - 20240709 mcm50 4812 491 chip3,4,5 bit 0x2 x - 20240709 mcm60 3C11 413 global reset bit error p - 20240628 mcm163 6A13 800 bit error chip3,4 (grst,ramp,pulser,data) p - 20240712 mcm171 7611 686 bit error on chip 3&4 p - 20240701 mcm172 7417 695 ADC after DAC init (action 3), data strange all over NOTE: 3 mcm (50,163,171) have bit errors on chip 3,4(&5). retested: x c 20240712 mcm20 300F 573 x - 20240716 mcm33 3E11 134 chip4,5 no answer x - 20240716 mcm50 4812 491 chip3,4 bit 0x2 c_1v5 2V x c 20240716 mcm60 3C11 413 x - 20240716 mcm163 6A13 800 bit error chip3,4 0x80 x - 20240716 mcm171 7611 686 bit error on chip 3&4 0x80 c_1v5 low x - 20240716 mcm172 7417 695 incm=225 ca as refn NOTE: testcard reapairs: chip7 chan0 no signal: soldering improved bit errors+programerror(?): resoldering connector mcm20+21: op changed 20240813 ======== mcm21 ----- changed op again refp 986mV->341mV incm 1106 mV cmout 804 mV refn 243 mV cmref 2126 mV DAC pin mV 1 2245 2 480 3 1368 4 729 5 2046 6 150 mcm52 ----- DTC terminator - wired traceid 8215 chip 3,4,5 no reply chip 2 strange register values 2136D mcm140 ------ OK(?) mcm172 ------ refn = incm DAC pin: mV 1 2440 2 505 3 1346 4 769 5 2045 6 153 DAC settings: decay 250 refp 675 cm 375 refn 75 20240903 ======== MCM21. Bytt OP för refP. verkar nu OK oansluten till SALTRO. Felet kurerat. Ett nytt problem är att på den andra OPn ser vi en liten skillnad mellan DAC spänning på 730mV och OP ut ca 16mV lägre. Så var det inte innan så problemet är nytt. Inte ansluten till SALTRO. Björn säger, kanske värmning på grann op kan ha öppnat lödning på denna OP. Lennart frågar om ev. flussmedel. Vi vet inte rengöra kan vi förstås försöka. MCM172. OP-systemet verkade funka när vi var frikopplade från SALTRO. 22ohmare åter på plats. Felet samma som tidigare. Slutsats. Felet någonstans nedströms 22ohmaren. Inget vi kan åtgärda. 20240909 ======== mcm160 - - 20240628 mcm160 ---- 271 programming; Expected: 0x612B4043 Read: 0x00000000 - - 20240712 mcm160 ---- 271 (Expected: 0x612B4043 Read: 0x00000000). U5 Vcore regulatorn saknas. 20240924 ======== mcm40 1.5V ca 1A mcm160 regulator pålödd program OK traceid 1A15 tested OK mcm52 chip 0,1,6,7 hangs mcm21 currents 1.5V,2.5V mcm50 chip 0,1,2,5,6,7 OK mcm171 chip 0,1,2,5,6,7 OK mcm163 chip 0,1,2,5,6,7 OK mcm33 chip 0,1,2,3,6,7 bit error 20240930-20241001 ================= pedestal tests with old LVCARD mcm40 1.5V 1A mcm70 can not read CPLD 20240930 mcm70 OK 20241001 mcm21 high current mcm11 SALTRO 539->518 mcm141 high pedestal ca ch 64 mcm155 some runs chip0&7 have pedestals = 0 for gain=0 mcm171 exclude chip3&4 OK mcm163 exclude chip3&4 OK mcm33 exclude chip4&5 biterror mcm50 exclude chip3&4 OK BAD === x -x 20240924 mcm21 3C0F 558 vrefp,incm wrong (op changed) x x- 20240930 mcm21 3C0F 558 high current x -x 20240716 mcm33 3E11 134 chip4,5 no answer x -x 20240924 mcm33 3E11 134 exclude chip4,5 bit errors x x- 20241001 mcm33 3E11 134 exclude chip4,5 bit errors x -x 20240924 mcm40 7411 97 1.5V 1A x x- 20240931 mcm40 7411 97 1.5V 1A x - 20240924 mcm52 8215 662 chip 3,4,5 no reply x - 20240924 mcm52 8215 662 chip 3,4,5 excluded, hangs p -x 20240701 mcm172 7417 695 ADC after DAC init (action 3), data strange all over x -x 20240716 mcm172 7417 695 incm=225 ca = as refn PARTLY ====== x -x 20240716 mcm50 4812 491 chip3,4 bit 0x2 c_1v5 2V x ex 20240924 mcm50 4812 491 exclude chip 3,4 from readout then OK x xe 20241001 mcm50 4812 491 exclude chip 3,4 from readout then OK p cx 20240628 mcm140 722E 098 chip6 chan 8: slope up when pulsing x cx 20240813 mcm140 722E 098 ok(no slope?) slope when humid? p cx 20240628 mcm153 5E14 677 x xc 20241001 mcm153 5E14 677 sometimes for full run gain0: chip0&7 ped=0 p -x 20240628 mcm163 6A13 800 bit error chip3,4 (grst,ramp,pulser,data) x -x 20240716 mcm163 6A13 800 bit error chip3,4 0x80 x ex 20240716 mcm163 6A13 800 exclude chip3,4 x xe 20241001 mcm163 6A13 800 exclude chip3,4 p -x 20240712 mcm171 7611 686 bit error, chip 3&4 x -x 20240716 mcm171 7611 686 bit error on chip 3&4 0x80 c_1v5 low x ex 20240924 mcm171 7611 686 exclude chip3,4 x xe 20241001 mcm171 7611 686 exclude chip3,4